Каталог статей
Меню сайта

Категории раздела
Мои статьи [17]

Корзина
Ваша корзина пуста

· RSS 19.02.2019, 02:04

Главная » Статьи » Мои статьи

Коды ошибок Коды ошибок копировальных аппаратов Xerox
Xerox 1012, 1012(RE)
Код ошибкиОписание
E1Jam between paper feed and fuser
E3Jam in fuser
E5Clam shell open
E6Paper feed section cover is open
J1Toner cartridge near empty
J3Drum cartridge not seated properly
J7Waste toner full (replace drum cartridge)
L6Key counter out
L8Exposure area overheat
U1No clock pulse (drive problem)
U2Scan problem
U3Lens/mirror problem (RE model only)
U4Heat problem
U8Exposure lamp control circuit problem
E1Jam between paper feed and fuser
E3Jam in fuser
E5Clam shell open
E6Paper feed section cover is open
J1Toner cartridge near empty
J3Drum cartridge not seated properly
J7Waste toner full (replace drum cartridge)
L6Key counter out
L8Exposure area overheat
U1No clock pulse (drive problem)
U2Scan problem
U3Lens/mirror problem (RE model only)
U4Heat problem
U8Exposure lamp control circuit problem

Xerox 1020
Код ошибкиОписание
LLProbable bad heater lamp

Xerox 1025
Код ошибкиОписание
A1DF jam
C1PF jam cass. 1
C2PF jam cass. 2
C3PF jam cass. 3
C9Bypass jam
E1-1Paper jam before exit switch
E1-2Paper jam
E1-5Paper jam
E1-6Paper jam
E3-3Paper jam at exit switch
E3-4Paper jam at exit switch
E5Front door open
F1Collator jam
F5Collator interlock
F8No power to collator
F9Collator bin home switch
J7250 copies since toner waste was full
L5Original cass. not present after clearing interrupt
L6Key counter
L8Platen glass too hot
U1Main motor clock pulse
U2Scan problem
U3-1Lens problem
U4-1Open thermistor
U4-2Low temperature
U4-4Temperature
U4-5Main PWB
U6-1Main PWB
U6-2Main PWB
U6-3Main board battery
U6-4Initialization
U8Exposure lamp

Xerox 1035
Код ошибкиОписание
A9Scanner location
C1Paper feed - upper cassette
C2Paper feed - lower cassette
C9Bypass jam
E5Clam shell is open
L6Key counter
U1Off/On
U2Optics
U4Low fuser temperature

Xerox 1038
Код ошибкиОписание
A1DF jam
C1PF jam cass. 1
C2PF jam cass. 2
C3PF jam cass. 3
C9Bypass jam
E1-1Paper jam before exit switch
E1-2Paper jam
E1-5Paper jam
E1-6Paper jam
E3-3Paper jam at exit switch
E3-4Paper jam at exit switch
E5Front door open
F1Collator jam
F5Collator interlock
F8No power to collator
F9Collator bin home switch
J7250 copies since toner waste was full
L5Original cass. not present after clearing interrupt
L6Key counter
L8Platen glass too hot
U1Main motor clock pulse
U2Scan problem
U3-1Lens problem
U4-1Open thermistor
U4-2Low temperature
U4-4Temperature
U4-5Main PWB
U6-1Main PWB
U6-2Main PWB
U6-3Main board battery
U6-4Initialization
U8Exposure lamp

Xerox 2830
Код ошибкиОписание
A9Scanner location
C1Paper feed - upper cassette
C2Paper feed - lower cassette
C9Bypass jam
E5Clam shell is open
E5Clam shell open
L6Key counter
U1Off/On
U2Optics
U4Low fuser temperature

Xerox 5011, 5012, 5014
Код ошибкиОписание
C8Bypass jam/no paper
C9Bypass jam
E1Jam
E3Fuser jam
E5Clamshell open
E6PF section cover open
J1Toner cartridge amost empty
J3Copy cart (drum unit) missing/not seated right
J7Copy cartridge has run 18,000 copies
J8Copy cartridge. Improperly seated or possible only one of two fuses in the cartridge blew
L6Key counter
L8Exposure glass too hot
U1Drive problem
U2Scan problem
U3Lens or mirror drive problem
U4Fuser problem. Heat lamp, thermoswitch, SSR, thermistor
U6Battery on main board
U8Exposure lamp or exposure lamp circuit

Xerox 5016, 5017, 5316, 5317
CodeDescription
A1-1Document feeder feed jam
A1-2Document feeder belt jam
A2-1Document feeder exit jam
A2-2Duplex jam
A3DAD interlock
A5Duplex and DAD right side interlock
A6Copier jams after
A9Document feed belt drive motor
C1-3Top cassette misfeed
C2-3Middle cassette misfeed
C3-3Bottom cassette misfeed
C9-3Bypass misfeed
E1-11 to E1-14Paper jam in machine. Did not reach exit switch soon enough
E1-6Paper path jam
E3-31 to E3-34Exit switch jam
E3-6Fuser jam
E5Front door interlock
E6Right side interlock or TTM interlock
F1Sorter jam
F5Sorter interlock
F8Sorter board to copier main board communication problem
F9Sorter bins

Xerox 5018, 5028
CodeDescription
A1Document is ADF
A1-8Main board received reset signal
A2ADF jams
A6, A7ADF jams
A9ADF jams
C1 - C4Feed jam
C5-1 to C5-4Jams in various areas
C5-2Jams in various areas
C5-3Jams in various areas
C5-4Duplex jam
E0Machine has reset
E1Jam
E1-E0Registration jam
E1-E5Clamshell interlock
E1-E6Right side interlock
E1-E7Two tray interlock
E1-E8Sorter interlock
E1-E9Copy cartridge interlock
E2Reset signal happened
E3Jam
E4Exit jam
E4-10Exit jam
E4-5Clamshell interlock
E4-6Right side interlock
E4-7Two tray interlock. Duplex interlock
E4-8Sorter interlock
E4-9Copy cartridge interlock
E5Clamshell interlock
E6Right side interlock
E7Duplex interlock
E9Copy cartridge interlock
F3-1Sorter bin home switch
F3-2Sorter cam switch
F3-3Sorter cam switch
J1-1Add toner
J1-2Temporary low toner signal
J2-0Replace copy cartridge
L22000 copies left on copy cartridge
L3ADF to machine communication problem
L4 (flashing)1000 copies left on fuser web
rrBad EPROM on main board
U0Main board
U2Scan problem
U2-1Scan home
U3-00Cam drive problem
U3-01Cam movement slow
U3-04Main board to duplex communication
U3-09Cam problem
U3-12Jogger problem
U3-19Cam problem
U3-21Cam problem
U3-23Cam problem
U3-29Cam problem
U3-32Cam problem
U3-34Cam problem
U3-39Cam problem
U3-43Cam problem
U3-45Cam problem
U3-49Cam problem
U3-54Cam problem
U3-56Cam problem
U3-59Cam problem
U4-1Fuser problem. Long warm up
U4-2Low fuser temperature after warm up
U4-3High fuser temperature
U4-4Open fuser thermistor
U4-6Replace fuser web
U4-7Thermistor signal problem
U7-1Copy cartridge belt drive problem
U9-3Exposure lamp problem
U9-4Toner motor
U9-5Problem in warm up

Xerox 5312, 5313, 5314
Код ошибкиОписание
C1Upper paper feed problem. Did not reach feed sensor
C2Lower paper feed problem. Did not reach feed sensor
E1Exit jam. Paper did not reach exit sensor
E3Exit jam. Paper still on exit sensor
J1Add toner
J3Copy cartridge (drum unit) not installed
J7Copy cartridge (drum unit) must be replaced
J8Copy cartridge (drum unit) problem
L6Problem with an accessory. Installed but not initialized
U1Drive problem. Main motor, gear etc.
U2Scan problem
U3Main board dip switches wrong. Lens drive problem
U4Fuser problem. Heat lamp, thermal switch, overheat, thermistor.
U6EPROM error
U8Auto exposure sensor. No exposure lamp or weak lamp

Xerox 5318, 5320, 5322
CodeDescription
A1-11Original ready switch
A1-12Feed sensor
A1-1 to A1-32All indicate a paper path problem, etc. in the ADF
A1-21Original ready switch and document registration sensor or both the document feed sensor and document registration sensor
A1-22ADF registration sensor
A1-23Original did not reach ADF registration sensor quickly enough
A1-24ADF sensor stuck down too long
A1-25ADF sensor actuated at the wrong time during single sheet feed
A1-26ADF sensor not actuated quickly enough in sheet feed mode
A1-31In reverse, ADF sensor is not actuated soon enough
A1-32In reverse, ADF sensor is actuated too long
A2ADF exit problems
A2-1Original ready sensor and ADF exit switch are actuated or ADF feed in sensor and ADF exit switch are both actuated
A2-2ADF exit switch
A2-3ADF exit switch is not actuated on time
A3Irregular size documents
A3-1Wrong size original sensed in 1:1 mode
A3-2Wrong size original sensed in the 2:1 mode
A5ADF interlock
A5ADF interlock
A6ADF single sheet document reset.
A6-1Reset original
A6-2Reset sheet feeder
A7Document cover interlock
A8ADF exit interlock
C1Tray 1 jam
C1-2Paper feed problem in tray 1
C1-3Paper does not reach registration
C2Tray 2 jam
C3Tray 3 jam
C3-1Paper feed problem from tray 3
C3-2Paper feed problem from tray 3
C3-3Paper feed problem from tray 1
C6-1Duplex paper feed problem
C6-2Duplex and/or tray 1 paper feed problem
C6-3Paper feed problem from tray 1
C7-1Paper feed problem from HCF
C7-2Paper feed problem from HCF on tray 1
C7-3Paper feed problem from tray 1
C8Paper stays in tray or duplex or HCF
C8-1Paper on tray 1 feed sensor
C8-2Paper on tray 2 feed sensor
C8-3Paper on tray 3 feed sensor
C8-4Paper on HCF feed sensor
C8-5Paper in duplex section
C9Bypass feed problem
C9-3Paper from bypass did not reach registration sensor quickly enough
E1-10 to E1-25Internal jam
E1-6Paper on registration sensor
E2Reset signal happened. Might read E-2 something else.
E3-30 to E4-14Exit jam
E3-30 to E3-35Exit switch actuated too long
E3-6Exit jam
E3-6Paper on exit switch
E4-10 to E4-14Inverter sensor not actuated.
E4-10 to E4-45Paper did not reach inverter switch soon enough
E4-15Inverter sensor
E4-40 to E4-45Duplex entry sensor
E4-6Paper on inverter switch
E4-6Inverter sensor
E5Front door interlock
E6-1Tray 1 interlock
E6-22 tray or duplex interlock
E6-3HCF interlock
E7-2Duplex inverter interlock
E7-3Duplex interlock
E8-10 to E8-15Paper on duplex feed sensor is not actuated soon enough
E8-6Paper in duplex
E8-6 to E8-15Duplex entry sensor
F1-1Paper did not reach sorter
F1-2Paper stayed on sorter feed sensor
F1-6Sorter exit sensor
F3Paper size not available for sort/stack
F5Sorter interlock
H2-1Communication problem between main board and duplex board
H2-2Side guard sensor problem
H3-1Communication problem between main board and HCF
H3-2Upper limit sensor problem on HCF
H6-1ADF size sensor
H6-2ADF nudgeer sensor
H6-3Belt drive motor does not have 24 volts. Black toner is empty, but 100 copies have been run without changing toner
J1Black toner is empty, but 100 copies have been run without changing toner
J3Replace copy cartridge
J3No copy cartridge (drum unit)
J7Copy cartrige must be replaced
J8-1Wrong copy cartridge installed
J8-2Copy cartridge EEPROM must be changed
L6Auditron or other counter problem
L6Key counter not installed
L8Platen glass temperature is too high
L9Communication problem between interimage erase/edge lamps and main board
U1-1Main motor drive problem
U2-1Scan home problem
U2-1 to U2-4Scan home sensor
U2-2Scan home problem or optics problem
U2-3, U2-4Scan home problem
U3-1Lens sensor problem
U4-1Fuser thermistor open
U4-2Fuser did not warm up properly
U4-3Fuser temperature too high
U4-4Fuser problem. Staying on too long
U4-6High fuser temperature
U5-1Sorter bin home switch not activated
U5-2Sorter bin home switch stayed actuated
U5-3Sorter bin home switch
U5-4Sorter bin home switch
U6-1ROM problem
U6-2RAM problem
U6-3Low battery
U6-4Incorrect value in NVM. Reinitialize main board with code 20-96
U8-1Exposure lamp problem
U8-2Communication problem main board and exposure board
U8-3Exposure lamp or exposure lamp board problem
U8-4 to U8-6Problem with exposure lamp, lamp sensor, lamp board
Категория: Мои статьи | Добавил: Онже (22.12.2013)
Просмотров: 1166 | Рейтинг: 0.0/0
Всего комментариев: 0
Добавлять комментарии могут только зарегистрированные пользователи.
[ Регистрация | Вход ]
СЦ "Звезда" Киселевск © 2019
Конструктор сайтов - uCoz