Каталог статей
Меню сайта

Категории раздела
Мои статьи [17]

Корзина
Ваша корзина пуста

· RSS 23.01.2019, 22:43

Главная » Статьи » Мои статьи

Коды ошибок копировальных аппаратов Toshiba копировальных аппаратов Toshiba
Toshiba 1210
Код ошибкиОписание
C1Copy table position error
C2Paper is not fed from the tray when the copy table starts moving
C3Copy table drive error
C4Copy table position error
C5Copy table end position error
C6Copy table position error at the end of the copy cycle
C7Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8Thermofuse blown
CPMain drive overloaded
CAMain Board defective
E1Paper jam
E2Fuser jam
E3Paper jam at start-up
E5Paper jam in the tray
E7Paper jam in the registration area

Toshiba 1310
Код ошибкиОписание
C5Copy table drive overloaded
C7Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CEEPROM defective or missing
CPMain drive overloaded
CDEPROM end of life
CFDevelopment unit not properly installed or defective
E0Used toner collection bottle full
E1Paper jam
E2Fuser jam
E3Paper jam at start-up
E5Paper jam in the tray
E6Paper jam at by-pass or defective sensor

Toshiba 1340, 1350
Код ошибкиОписание
C5, C6Scan problem
C7Fuser problem (reset with 0 + 8 mode, code 89)
CEMissing EEPROM
CFBoard problem
CPDrive problem
E1Paper jam
E2Fuser jam
E3Paper jam
E5Paper feed jam
E0Toner waste bottle is full

Toshiba 1550
Код ошибкиОписание
C01Main motor drive problem
C21Optics problem Scan , lens, mirror
C26Exposure lamp detect problem
C32Setup error (UA)
C41Fuser thermistor, or no heat
C43Fuser thermistor problem or other fuser problem, after machine goes into ready
C44Heater problem
C54Communication problem between sorter and machine main board
C55Communication problem between ADF and machine main board
C71ADF drive problem
C72ADF registration sensor problem
C73EEPROM initialization problem
C81Sorter paper conveying motor
C82Sorter bin motor
C83Sorter upper sensor
C84Sorter lower sensor
C85Sorter home sensor
C86Sorter copy removal sensor
C94Optics initialization problem in test modes
E01Paper jam
E02Fuser jam
E03Paper jam at startup
E05Paper jam in the registration area
E14Lower cassette jam
E71, E72, E73ADF jam
E75ADF jam of 2nd original
E81, E82Sorter jam

Toshiba 1560
Код ошибкиОписание
C01Main motor drive overloaded
C21Optics problem Scan , lens, mirror
C26Exposure lamp blown, or bad contacts
C32Easy set-up error
C41Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C43, C44Abnormal temperature in the fuser, thermistor error
C54Communication with the sorter is intrerrupted
C55Communication with the feeder is intrerrupted
C71Top Feeder motor overloaded
C72Sensor problem in the feeder
C73Feeder EPROM initialization error
C81Sorter paper transport motor overloaded
C82Sorter shift tray motor overloaded
C83Upper position error in the sorter
C84Lower limit position error in the sorter
C85Home position error in sorter
C88Paper sensor error in sorter
C94Optical system initialization error
E01Paper jam
E02Fuser jam
E03Paper jam at startup
E05Paper jam in the registration area
E14Paper jam in the Paper Feed Unit
E71Original jammed in the top feeder
E72Original jammed during transport in the top feeder
E73Original jam at the feeder exit
E75Original jammed
E81, E82Sorter jam

Toshiba 1650
Код ошибкиОписание
A4Sorter problem
A5Communication problem between main CPU and IPC
A6Sorter interface problem
C2Communication problem between CPU's
C5Scan or optic problem. Locked up or won't initialize or return to home position
C7Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CFDeveloper calibration problem
CPDrive problem
E1Paper jam
E2Fuser jam
E3Paper jam
E4Front door opened during copy cycle
E5Paper feed jam

Toshiba 1710
Код ошибкиОписание
A1Charge corona cleaner problem
A2ADD problem
A4Sorter problem
A5Board problem
A6Sorter board problem
A7ADF interface
A0 Communication problem between main board and PFC
C1Board problem
C2Board problem
C3Board problem
C4Board problem
C5Optics locked or not initialized. Could be scan or lens/mirror
C7Fuser thermistoe problem, or low temperature
C8Scan motor won't shut off
CAMain board problem
CBADF drive problem
CCADF drive problem
CDBC RAM hardware
CEBC RAM software
CPDrive problem
E0Waste toner full
E1Jam
E2Fuser jam
E3Jam
E4Front door was opened during copy run
E5Feed jam
E8Jam in ADD (duplex)
E9Jam in pedestal
ECADF jam
EDADF jam
EEADF exit/reverse jam

Toshiba 2050
Код ошибкиОписание
A4Sorter problem
A5Communication problem between main CPU and IPC
A6Sorter interface problem
C2Communication problem between CPU's
C5Scan or optic problem. Locked up or won't initialize or return to home position
C7Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CFDeveloper calibration problem
CPDrive problem
E1Paper jam
E2Fuser jam
E3Paper jam
E4Front door opened during copy cycle
E5Paper feed jam

Toshiba 2060
Код ошибкиОписание
C01Main motor drive problem
C04Pedestal main drive problem
C05Duplex drive problem
C11Duplex exit motor
C12Duplex end motor
C13Upper cassette
C14Lower cassette
C15Pedestal upper cassette
C16Pedestal middle cassette
C17Pedestal lower cassette
C18LCT
C21Scan problem
C22Lens problem
C23Mirror motor
C26Exposure lamp
C27Scan motor
C33Set up failure
C35Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up
C44Fuser problem after warm-up
C45Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01Jam
E02Fuser jam
E03Jam at turn on
E04Front door opened during copy cycle
E05Registration jam
E08Duplex unit jam
E11Duplex jam
E12Bypass jam
E13Upper cassette jam
E142nd cassette jam
E153rd cassette jam
E164th cassette jam
E174th cassette jam
E19 CT jam
E21LCT jam
E22-E25Paper jams in copier
E71ADF feed jam
E72ADF transport jam
E73ADF exit jam
E74RADF jam
E75ADF 2nd original jam
E81-E85Sorter jam
E88Jam after sorter

Toshiba 2310
Код ошибкиОписание
A1Charge corona cleaner problem
A2ADD problem
A4Sorter problem
A5Board problem
A6Sorter board problem
A7ADF interface
A0Communication problem between main board and PFC
C1Board problem
C2Board problem
C3Board problem
C4Board problem
C5Optics locked or not initialized. Could be scan or lens/mirror
C7Fuser thermistoe problem, or low temperature
C8Scan motor won't shut off
CAMain board problem
CBADF drive problem
CCADF drive problem
CDBC RAM hardware
CEBC RAM software
CPDrive problem
E0Waste toner full
E1Jam
E2Fuser jam
E3Jam
E4Front door was opened during copy run
E5Feed jam
E8Jam in ADD (duplex)
E9 Jam in pedestal
ECADF jam
EDADF jam
EEADF exit/reverse jam

Toshiba 2500
Код ошибкиОписание
A1Charge corona cleaner problem
A2ADD problem
A4Sorter problem
A5Board problem
A6Sorter board problem
A7ADF interface
A0Communication problem between main board and PFC
C1Board problem
C2Board problem
C3Board problem
C4Board problem
C5Optics locked or not initialized. Could be scan or lens/mirror
C7Fuser thermistoe problem, or low temperature
C8Scan motor won't shut off
CAMain board problem
CBADF drive problem
CCADF drive problem
CDBC RAM hardware
CEBC RAM software
CPDrive problem
E0Waste toner full
E1Jam
E2Fuser jam
E3Jam
E4Front door was opened during copy run
E5Feed jam
E8Jam in ADD (duplex)
E9 Jam in pedestal
ECADF jam
EDADF jam
EEADF exit/reverse jam

Toshiba 2510
Код ошибкиОписание
A1Charge corona cleaner problem
A2ADD problem
A4Sorter problem
A5Board problem
A6Sorter board problem
A7ADF interface
A0Communication problem between main board and PFC
C1Board problem
C2Board problem
C3Board problem
C4Board problem
C5Optics locked or not initialized. Could be scan or lens/mirror
C7Fuser thermistoe problem, or low temperature
C8Scan motor won't shut off
CAMain board problem
CBADF drive problem
CCADF drive problem
CDBC RAM hardware
CEBC RAM software
CPDrive problem
E0Waste toner full
E1Jam
E2Fuser jam
E3Jam
E4Front door was opened during copy run
E5Feed jam
E8Jam in ADD (duplex)
E9 Jam in pedestal
ECADF jam
EDADF jam
EEADF exit/reverse jam

Toshiba 2532
Код ошибкиОписание
A4Sorter problem
A5Communication problem with main board
A6Communication problem with sorter
A7Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2Communication problem between main board
C5Scan won't initialize or won't move
C7Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CCADF belt motor or exit motor not turning
CFAuto toner adjustment did not take
CPDrive problem in machine
E1Jam
E2Fuser jam
E3Jam
E4Front door was opened during copy cycle
E5Feed jam

Toshiba 2540
Код ошибкиОписание
A4Sorter problem
A5Communication problem with main board
A6Communication problem with sorter
A7Communication problem with ADF
A9 Exposure lamp problem or auto exposure problem
C2Communication problem between main board
C5Scan won't initialize or won't move
C7Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CCADF belt motor or exit motor not turning
CFAuto toner adjustment did not take
CPDrive problem in machine
E1Jam
E2Fuser jam
E3Jam
E4Front door was opened during copy cycle
E5Feed jam

Toshiba 2550
Код ошибкиОписание
A2Duplex functional problems
A4Sorter problem
A5Communication lost with the sorter
A6Communication problems with the sorter interface
A7Communication problems with the feeder
A9Exposure lamp blown, or bad contacts
C2, C3Processor to subprocessor communication problems
C5Optical system initialization error
C7Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CBOriginal feed motor overloaded in the feeder
CCOriginal transport motor overloaded in the feeder
CFToner density error
CPMain motor drive overloaded
E1Paper jam detected in machine
E2Paper jam in the fusing area
E3Paper jam at start-up
E4Front cover open during copy cicle
E5Paper feed jam in the paper tray
E8Paper jam in the duplex unit
E9Paper jam in the optional paper feed unit
ECOriginal misfeed in the feeder
EDOriginal jam in the feeder
EEOriginal jam at the feeder inverter or exit area

Toshiba 2810
Код ошибкиОписание
C1Scan did not return home
C3Scan home sensor
C4Scan problem
C5Scan limit sensor
C6Scan did not return
C7Thermistor or other fuser problem
CCScan did not leave home
CPDrive
E1Jam inside machine
E2Fuser jam or exit jam
E3Exit switch or registration switch
E5Paper feed jam
E7Cassette or registration jam

Toshiba 2860
Код ошибкиОписание
C01Main motor drive problem
C04Pedestal main drive problem
C05Duplex drive problem
C11Duplex exit motor
C12Duplex end motor
C13Upper cassette
C14Lower cassette
C15Pedestal upper cassette
C16Pedestal middle cassette
C17Pedestal lower cassette
C18LCT
C21Scan problem
C22Lens problem
C23Mirror motor
C26Exposure lamp
C27Scan motor
C33Set up failure
C35Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41Fuser thermistor or low temperature
C43Fuser problem after warm-up
C44Fuser problem after warm-up
C45Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01Jam
E02Fuser jam
E03Jam at turn on
E04Front door opened during copy cycle
E05Registration jam
E08Duplex unit jam
E11Duplex jam
E12Bypass jam
E13Upper cassette jam
E142nd cassette jam
E153rd cassette jam
E164th cassette jam
E174th cassette jam
E19 CT jam
E21LCT jam
E22-E25Paper jams in copier
E71ADF feed jam
E72ADF transport jam
E73ADF exit jam
E74RADF jam
E75ADF 2nd original jam
E81-E85Sorter jam
E88Jam after sorter
Категория: Мои статьи | Добавил: Онже (22.12.2013)
Просмотров: 780 | Рейтинг: 0.0/0
Всего комментариев: 0
Добавлять комментарии могут только зарегистрированные пользователи.
[ Регистрация | Вход ]
СЦ "Звезда" Киселевск © 2019
Конструктор сайтов - uCoz